⚠️Due to high demand, processing times are 12-16 days.
Dross:Aviation LogoDross:Aviation
Shop
  • Stratux Devices
  • Sensors
  • Cases
  • Transmission (TX)
  • Antennas
  • Professional Services
StratuxProfessional Services
Comparisons
  • Stratux vs Sentry
  • Stratux vs SkyEcho
  • Stratux vs PowerFLARM
  • Stratux vs Rosetta
FAQ & Guides
DIY Guide
  • First Time Setup
  • Component Checklist
  • Install Firmware
  • Install VFR Charts
  • Calibrate SDR
  • Flash T-Beam
  • Flash T-Motion
  • AHRS & Altitude Sensor
  • Submit to OGN
  • Mobile Data While Connected
  • Garmin Pilot Setup
  • Troubleshooting: WiFi & GPS
  • SkyDemon Setup
  • Stratux Web Interface
Contact
🇬🇧EN🇩🇪DE🇪🇸ES
🇬🇧EN🇩🇪DE🇪🇸ES
  1. Home
  2. Dross:Aviation
  3. DIY Guide
  4. First Time Setup

Stratux First Time Setup Instructions

Complete guide to setting up your new Stratux device

What you need

A first setup takes about fifteen minutes indoors, plus one patient half hour outdoors for the GPS. Everything below is either in the box or something you already own.

  • The Stratux with its SD card. Cards from us arrive flashed with the EU firmware; if you built your own, write the image first.
  • Both receive antennas - one for 1090 MHz, one for 868 MHz. They are not interchangeable, and which connector takes which is worth checking once rather than guessing.
  • A 5 V supply that holds up at 2.5 A. A USB power bank is ideal for the first test on the ground; in the aircraft, a socket that does not brown out when the avionics come alive.
  • A micro-USB-B cable, short and shielded. A long thin phone cable is the single most common cause of a Stratux that reboots in flight.
  • A tablet or phone with your EFB app installed and its charts already downloaded - on the Stratux network there is no internet to fetch them over.
  • Optional, for an artificial horizon and synthetic vision: an AHRS sensor board inside the unit. Traffic and position work perfectly well without one.
Write the EU firmwareAntenna guideAHRS sensor boards

First power-up, and what should happen

Nothing here needs a keyboard or a login. The unit boots on its own and starts serving data to anything that joins its network.

  1. 1Screw both antennas on before you apply power. Running a receiver bare will not hurt it, but you will spend the next half hour chasing a reception problem you created yourself.
  2. 2Apply power. After roughly half a minute a WiFi network named "stratux" appears; it is open unless you set a password yourself. Your device will warn that the network has no internet, which is correct and harmless.
  3. 3Give the GPS its cold start outdoors, not in the car - a car body is a Faraday cage and will cost you satellites. The first fix takes a few minutes. Once, leave the unit running outside for half an hour so it can store the full almanac; every later start then fixes in seconds.

Running it on the aircraft bus: treat it like a radio

Wired permanently into the aircraft's electrical system, the Stratux follows the same order as the radio: switch it on only once the engine is running, and shut it down before you stop the engine. Starting and stopping an engine puts voltage transients on the bus that can permanently damage sensitive electronics. Keeping to that order holds the device clear of them.

Watching the box for signs of life while it boots? What the lights do and do not tell you

What the two receivers actually bring you

A Stratux listens on two frequencies at once, and in Europe that second one is the reason the box is worth having: it is where the traffic lives that no airliner-grade receiver ever sees.

1090 MHz

ADS-B and Mode S: airliners, most IFR traffic and every GA aircraft carrying ADS-B Out. Worldwide, same on both firmware builds.

868 MHz

With the EU firmware: FLARM-compatible traffic, OGN, ADS-L, FANET and PilotAware. Gliders, paragliders, microlights - the aircraft you actually share a thermal or a circuit with.

GPS and barometer

A position good enough to navigate on and a pressure altitude, both handed to your EFB so it stops relying on the tablet's own receiver.

978 MHz UAT, the band that carries FIS-B weather, is a US ground service with no European counterpart. Weather in your EFB comes over the internet instead.

Frequency guideFLARMOGNADS-B

Stratux Versions

Placement that decides your range

  • Both the 868 and 1090 MHz antennas belong upright, at a right angle to the horizon. Aircraft transmit vertically polarised, and an antenna lying flat throws away most of what reaches it.
  • Give the GPS antenna sky, not headliner. Under a metal roof or down in the footwell it will find few satellites and hold them badly.
  • Keep some distance from other electronics, and especially from a phone charging on a cheap adapter - switching supplies are noisy right across the bands you are trying to hear.
  • Mount it where it can shed heat and where you can still reach it. Behind a windscreen in summer sun a Raspberry Pi will throttle itself, and a throttled Pi drops traffic messages.

The built-in web interface

  • With your device on the stratux network, open http://192.168.10.1 in any browser. Android users can use the Stratux Manager app instead; nothing has to be installed on iOS.
  • The status page is your diagnostic tool for everything that follows: satellites in view, whether both SDRs were recognised, how much traffic is coming in and which devices are connected.
  • If an AHRS board is fitted, tell the settings page which way the box is mounted. The sensor cannot guess its own orientation, and a wrong answer tilts your artificial horizon.
  • Flying somewhere shared, a club aircraft or a busy apron? Set a WiFi password on the settings page so nobody else joins the network your EFB is using.
Web Interface GuideRoastbeef Web InterfaceGxAirCom Web Interface

Pointing your EFB app at the Stratux

Two protocols are on offer and the choice matters in Europe. GDL90 is pushed out by the Stratux over UDP port 4000 to every device on its network and carries AHRS data. FLARM-NMEA waits for the app to connect on TCP port 2000 and handles bearingless targets - a FLARM contact without a direction - better than GDL90 does. Several apps speak both; where that is the case, the recommended one is marked.

SkyDemonFLARM-NMEArecommended

192.168.1.1:2000

Settings - Third-Party Devices - enable FLARM Devices, then pick "Air Avionics AT-1" or "FLARM via AirConnect". Choose the same device again under Go Flying.

Full SkyDemon walkthrough
SkyDemonGDL90

192.168.10.1:4000

Settings - Third-Party Devices - enable "GDL90 Compatible Device". Workable, but it shows bearingless contacts less well than the FLARM route above.

ForeFlightGDL90

192.168.10.1:4000

Nothing to configure - it finds the Stratux once you are on the network and lists it under its devices. In Europe, switch on the bearingless-target circles first; our walkthrough explains why.

Full ForeFlight walkthrough
Garmin PilotGDL90

192.168.10.1:4000

Devices - select Stratux. Supported from version 10.7 on; our own walkthrough covers the iOS permission that trips this up.

Full Garmin Pilot walkthrough
AIP:AeroGDL90recommended

192.168.10.1:4000

Enable GDL90 traffic in the settings and the moving map draws the Stratux's targets straight onto the official AIP charts of 62+ countries. It needs no installation - the browser version runs on any tablet, which also makes it the quickest way to check a new receiver is working. From the same house as this shop.

EasyVFR 4GDL90 / FLARM-NMEA

192.168.10.1 / 192.168.1.1

Configuration - System - Location (GPS) source: Automatic detects the Stratux by itself; pick FLARM (TCP) for the NMEA route.

EasyVFR 3GDL90 / FLARM-NMEA

192.168.10.1 / 192.168.1.1:2000

Settings - GDL90 Settings: enable Use GDL90 and Use GDL90 GPS as EasyVFR GPS. For NMEA instead: Settings - FLARM Settings, WiFly IP 192.168.1.1, port 2000.

XCSoarFLARM-NMEA

192.168.10.1:2000

Config - Devices - pick a free port - Edit: port type TCP Client, address 192.168.10.1, TCP port 2000, driver FLARM.

Sky-MapGDL90recommended

192.168.10.1:4000

Setup - Wireless Interface Setup - Device: Stratux, no password, and let it use the Stratux GPS rather than the tablet's. Then switch the FLARM/ADS-B traffic display on and set your ranges.

AirmateGDL90

192.168.10.1:4000

iOS only. Set the ADS-B receiver to automatic and the GPS source to Stratux.

VFRnavGDL90

192.168.10.1:4000

Settings - FLARM/ADSB-IN configuration - select Stratux and name the WiFi network. It also reads the status data, so it can show you the unit's CPU temperature.

Enroute Flight NavigationFLARM-NMEA

192.168.1.1:2000

Finds the Stratux on its own once you are on its WLAN; the main menu shows the connection state.

SafeSkyGDL90

192.168.10.1:4000

Preferences - Traffic Sharing: name your EFB under Navigation and pick Stratux as the external traffic device. Enabling Relay traffic shares what you receive with the SafeSky community.

One caveat with two apps open at once: on some platforms an EFB claims UDP 4000 exclusively, and the second app then receives nothing. If one of them stays empty, close the other.

EFB compatibilityGDL90NMEA protocol

Per-app settings in the Stratux project wiki

The check before the first flight

Do this once on the ground, outdoors, ideally within sight of an airfield or under an approach path so there is something to receive.

  1. 1The status page reports a GPS fix, not just satellites in view.
  2. 2Both SDR receivers are listed. One missing means a loose dongle or a tired power supply, and you lose a whole band.
  3. 3The traffic counter climbs. Zero after several minutes outdoors points at an antenna, not at software.
  4. 4With an AHRS board, the artificial horizon follows when you tilt the unit - and tilts the right way.
  5. 5Your EFB shows the Stratux as connected and puts its targets on the map. If the status page is healthy and the app is empty, the problem is in the app's settings.
  6. 6If your own aircraft transmits - ADS-B Out, or a FLARM or OGN tracker - put its code into the settings. Without it the Stratux hands your own signal to your EFB and you spend the flight being warned about yourself.
  7. 7Calibrate the AHRS with the unit already in its flight position, not on the desk. It learns level from where it sits, so calibrating it somewhere else bakes in the error.
  8. 8Work out the power before you leave the ramp: a Pi with two SDRs draws steadily, so match the power bank to the leg you are flying rather than to the taxi out.
  9. 9Have the GPS fix before you taxi, and treat everything on the screen as an aid. A Stratux shows what transmits; see-and-avoid is still what keeps you apart from the rest.

When something does not come up

The stratux network never appears
Give it a full minute first. Then suspect the supply: a Pi that browns out during boot never gets as far as the access point. Try a different cable and a power bank you know holds 2.5 A before you suspect the SD card.
Connected, but no traffic at all
Check the status page rather than the app: if both SDRs are there and the message count is still zero, it is the antennas - swapped, loose, lying flat, or indoors. A Stratux only ever shows what transmits, so an aircraft with a Mode A/C transponder or none at all stays invisible no matter how well it is set up.
Your phone keeps leaving the network
Android sees a WiFi without internet and goes back to mobile data, taking your traffic feed with it. Switching the Stratux to WiFi Direct solves it properly and keeps your mobile data alive at the same time; we have a separate guide for exactly that.
Traffic works, weather does not
In Europe that is not a fault. Over-the-air weather is the FIS-B service on 978 MHz UAT, broadcast by FAA ground stations in the USA and by nobody here. European weather in your EFB comes over the internet, which is why the mobile-data question above matters.
Fewer contacts on 868 MHz than expected
The 868 MHz dongle usually needs its frequency offset calibrated before it hears FLARM and OGN properly; an uncalibrated receiver sits just far enough off to miss most of it. That is a ten-minute job, documented separately.
It reboots or slows down in flight
Heat and volts, in that order. Direct sun on a dark case will push a Pi into thermal throttling, and a long thin USB cable drops enough voltage under load to brown it out. Move it out of the sun, give it air, and shorten the cable.
What the lights meanFull troubleshooting guideKeep mobile dataCalibrate the 868 MHz SDRRegister with OGN

Switching it off

  • You can simply cut the power. Since firmware 1.6r1-eu026 the root partition is mounted read-only, so there is no half-written file to corrupt and the old physical shutdown button is no longer needed.
  • That read-only mount is also why nothing you change survives a restart unless you deliberately turn persistent logging on first.
  • If you do want to modify the firmware, disable persistent logging first - the steps are in the chart-installation guide, where the same switch is needed. We cannot warrant a unit whose firmware has been modified.
Persistent logging steps

Worth knowing

  • An AHRS sensor wants a few minutes of level, undisturbed time after power-up before its horizon settles.
  • Note down the firmware version from the status page. Every question about your unit, ours included, starts there.
  • Once it is receiving well, consider feeding what you hear into the open networks - your field gains coverage and so does everyone flying into it.
  • Two aircraft, one Stratux? Nothing is tied to a tail number, but set the AHRS orientation again if the box sits differently in the other one.

Next Steps

Now that your Stratux is set up, explore these additional resources:

Web Interface GuideInstall VFR ChartsCalibrate SDR

Disclaimer

Stratux is not certified aviation equipment. It does not replace a transponder or relieve the pilot of traffic awareness responsibilities. Use as supplementary situational awareness only. Dross:Aviation assumes no responsibility or liability for the use of Stratux devices, firmware flashing, or hardware modifications. All DIY guides are provided without warranty: use at your own risk.

Related Technology Guides

Stratux

Complete anti-collision system guide

Web Interface

Configure your Stratux at 192.168.10.1

EFB Apps

SkyDemon, ForeFlight compatibility

View all guides
Dross:Aviation

© 2026 All rights reserved.

Dross:Network|Alexander Dross|Dross:Media|Dross:Air|Blog|AIP:Aero|Trade:Aero
Shop|Services|Guides|Comparisons|DIY|Sitemap
Newsletter|Legal|Privacy|Imprint|Contact