⚠️Due to high demand, processing times are 12-16 days.
Dross:Aviation LogoDross:Aviation
Shop
  • Stratux Devices
  • Sensors
  • Cases
  • Transmission (TX)
  • Antennas
  • Professional Services
StratuxProfessional Services
Comparisons
  • Stratux vs Sentry
  • Stratux vs SkyEcho
  • Stratux vs PowerFLARM
  • Stratux vs Rosetta
FAQ & Guides
DIY Guide
  • First Time Setup
  • Component Checklist
  • Install Firmware
  • Install VFR Charts
  • Calibrate SDR
  • Flash T-Beam
  • Flash T-Motion
  • AHRS & Altitude Sensor
  • Submit to OGN
  • Mobile Data While Connected
  • Garmin Pilot Setup
  • Troubleshooting: WiFi & GPS
  • SkyDemon Setup
  • Stratux Web Interface
Contact
🇬🇧EN🇩🇪DE🇪🇸ES
🇬🇧EN🇩🇪DE🇪🇸ES
  1. Home
  2. Dross:Aviation
  3. FAQ
  4. Stratux Web Interface
  5. GxAirCom Web Interface

GxAirCom Web Interface

T-Beam FLARM/FANET Firmware

GxAirCom is an open-source firmware for the TTGO T-Beam and the preferred secondary choice alongside OGN-Tracker: it adds FLARM transmission (TX: FLARM and FANET), the one protocol OGN-Tracker cannot send. In a Stratux the SDRs receive all traffic, so the T-Beam's job is transmission. GxAirCom runs its own WiFi access point and configuration/status web interface, reachable in any browser at http://192.168.4.1/info.html.

See also:Standard InterfaceFLARMFANETSoftRF

Access URL

http://192.168.4.1/info.html

How to Access

  1. 1

    Power on your T-Beam flashed with GxAirCom and wait for it to boot

  2. 2

    Connect your phone or laptop to the GxAirCom WiFi access point (SSID: GxAirCom-xxxx)

  3. 3

    Open any web browser and navigate to http://192.168.4.1/info.html

  4. 4

    The Info/Status page loads - use the Config tab to set band, protocols, GPS and pilot details

GxAirCom is an alternative to OGN-Tracker for pilots who need to transmit on the FLARM protocol. See the Stratux GxAirCom integration wiki for wiring and Stratux-side configuration.

Web Interface Sections

01Info / Status

The info.html landing page shows live device status: GPS fix and satellites, battery voltage, board temperature, your own position, and the number of aircraft received and transmitted, plus the running firmware version.

Key Features:

  • GPS Fix & Satellite Count
  • Battery Voltage
  • Board Temperature
  • Aircraft Received / Transmitted
  • Firmware Version & Uptime

Screenshot 1

Info / Status

Screenshot of the GxAirCom web interface

02Configuration

The Config tab holds the general device settings: pilot name, aircraft type and address (ID), and display/power-save options. These identify your aircraft to other traffic on the network.

Key Features:

  • Pilot Name
  • Aircraft Type & Address (ID)
  • Display Options
  • Power-Save Settings
  • Save & Reboot

Screenshot 2

Configuration

Screenshot of the GxAirCom web interface

03Radio & Protocols

Select the radio band for your region and the transmit protocols. On a Stratux the SDRs receive all traffic, so what matters here is transmission - GxAirCom sends FLARM and FANET and lets you set the transmit power.

Key Features:

  • Band Selection (EU 868 / US 915 MHz)
  • TX: FLARM, FANET
  • Transmit Power
  • Legacy FLARM Compatibility
  • Traffic reception via the Stratux SDRs

Screenshot 3

Radio & Protocols

Screenshot of the GxAirCom web interface

04GPS

GxAirCom drives the T-Beam's GPS at up to 5 Hz with free configuration, so your transmitted position stays accurate and smooth. The status is shown live on the Info page.

Key Features:

  • Up to 5 Hz Update Rate
  • Free GPS Configuration
  • Satellite Status
  • Position Accuracy
  • NMEA Output

Screenshot 4

GPS

Screenshot of the GxAirCom web interface

05WiFi & Network

Manage how the device connects: it runs its own access point (GxAirCom-xxxx) at 192.168.4.1 for configuration, and can also join your home WiFi as a client for over-the-air updates and internet uploads.

Key Features:

  • Access Point Mode (192.168.4.1)
  • Client Mode (home WiFi)
  • AP SSID & Password
  • Internet Upload
  • OTA-Ready Connection

Screenshot 5

WiFi & Network

Screenshot of the GxAirCom web interface

06Firmware Update

Update GxAirCom straight from the browser: upload a new firmware binary over the web interface, or pull the latest release when the device is connected to the internet. No cables or flashing tools required.

Key Features:

  • Browser-Based OTA Update
  • Upload Firmware Binary
  • Version Check
  • No USB Cable Needed
  • Rollback Safety

Screenshot 6

Firmware Update

Screenshot of the GxAirCom web interface

Related Guides

Flash T-Beam

Install GxAirCom firmware

FLARM Guide

How FLARM anti-collision works

Stratux Web Interface

The Stratux interface at 192.168.10.1

Roastbeef Web Interface

The other advanced Stratux firmware interface

GxAirCom on GitHub

Official project & documentation

Important Note

While connected to the GxAirCom access point (192.168.4.1) your device has no internet access. To fetch firmware or upload flight data, either switch GxAirCom to client mode on your home WiFi or reconnect your phone to its regular network.

Frequently Asked Questions

Ready to set up GxAirCom?

Flash GxAirCom onto your T-Beam, then configure it from the web interface. Our guides walk you through every step.

Flash T-BeamAll GuidesContact
Dross:Aviation

© 2026 All rights reserved.

Dross:Network|Alexander Dross|Dross:Media|Dross:Air|Blog|AIP:Aero|Trade:Aero
Shop|Services|Guides|Comparisons|DIY|Sitemap
Newsletter|Legal|Privacy|Imprint|Contact