Connect a Stratux to SkyDemon
Two protocols, and the one you pick decides whether you see gliders without a bearing
SkyDemon is the most used EFB in European general aviation, and it is the one app where this connection is worth a page of its own. Not because it is difficult - both routes take about five minutes - but because the choice between them is made on the Stratux rather than in the app, and because one of them shows you traffic the other quietly drops.
The decision, and where it is actually made
There is no protocol dropdown in SkyDemon, which is what sends most people looking in the wrong place. The Stratux's own IP address is the switch: give it 192.168.1.1 and SkyDemon talks to it as a FLARM device over NMEA, leave it on 192.168.10.1 and it stays on GDL90.
192.168.1.1 ยท TCP 2000
What it gives you: Carries bearingless targets as SkyDemon expects them. A FLARM contact received without a usable direction - the normal case at range, and most of the glider traffic you care about - is drawn as a ring at the right distance instead of being discarded.
What it costs: No attitude: the artificial horizon from an AHRS board does not travel over this protocol.
192.168.10.1 ยท UDP 4000
What it gives you: Carries AHRS, so an attitude display is possible, and it is the same protocol every other EFB uses - handy if you switch apps often.
What it costs: Bearingless contacts only appear if you switch the Stratux's circle emulation on, and even then they are a reconstruction rather than what FLARM actually sent.
For flying in Europe, take FLARM-NMEA. The only reason to prefer GDL90 is wanting the AHRS horizon inside SkyDemon, and an attitude display is the one thing on a Stratux you should least rely on anyway.
Setting up the FLARM-NMEA route
- 1In the Stratux web interface, set the device's IP address to 192.168.1.1 and reboot. This single setting is what makes SkyDemon treat it as a FLARM device; nothing in the app corresponds to it.
- 2Join the stratux WiFi from your tablet, as usual.
- 3In SkyDemon, open Settings and then Third-Party Devices, switch FLARM Devices on, and choose either "Air Avionics AT-1" or "FLARM via AirConnect". Both reach the same receiver; pick whichever your build offers.
- 4Now the step that catches almost everybody: go to Go Flying and select that same device there as well. The settings page only declares what exists - Go Flying decides what this flight actually uses. Skip it and everything looks configured while nothing arrives.
- 5An AirConnect licence key is not needed. That field belongs to the commercial device of the same name; on a European Stratux build you leave it alone.
Setting up the GDL90 route
- 1Leave the Stratux on its default 192.168.10.1 - there is nothing to change on the receiver.
- 2In SkyDemon, under Settings and Third-Party Devices, enable "GDL90 Compatible Device".
- 3Select the same device again under Go Flying - the same trap as on the other route.
- 4Switch on bearingless target circle emulation in the Stratux settings, or the FLARM contacts without a direction will not reach the map at all.
What goes wrong with SkyDemon specifically
- SkyDemon shows nothing although the device is configured
- Almost certainly the Go Flying step. The settings page only declares which devices exist; Go Flying decides which one this flight uses. Select the same device in both places and the map fills.
- Charts or airspace are missing in flight
- Once you join the receiver's network there is no internet, so anything SkyDemon still meant to fetch is simply absent. Download everything you need before you walk to the aircraft.
- No weather appears
- SkyDemon's weather comes over the internet, not off the receiver, so it needs a live mobile connection alongside the WiFi. Switching the Stratux to WiFi Direct keeps mobile data alive while you stay connected to it.
- Very few FLARM contacts
- Look at the 868 MHz receiver rather than the app. An uncalibrated dongle sits far enough off frequency to miss most of the band while reporting itself perfectly healthy; calibrating its offset is a ten-minute job.
Per-app settings in the Stratux project wiki
Related Technology Guides
Disclaimer
Stratux is not certified aviation equipment. It does not replace a transponder or relieve the pilot of traffic awareness responsibilities. Use as supplementary situational awareness only. Dross:Aviation assumes no responsibility or liability for the use of Stratux devices, firmware flashing, or hardware modifications. All DIY guides are provided without warranty: use at your own risk.