⚠️Due to high demand, processing times are 12-16 days.
Dross:Aviation LogoDross:Aviation
Shop
  • Stratux Devices
  • Sensors
  • Cases
  • Transmission (TX)
  • Antennas
  • Professional Services
StratuxProfessional Services
Comparisons
  • Stratux vs Sentry
  • Stratux vs SkyEcho
  • Stratux vs PowerFLARM
  • Stratux vs Rosetta
FAQ & Guides
DIY Guide
  • First Time Setup
  • Component Checklist
  • Install Firmware
  • Install VFR Charts
  • Calibrate SDR
  • Flash T-Beam
  • Flash T-Motion
  • AHRS & Altitude Sensor
  • Submit to OGN
  • Mobile Data While Connected
  • Garmin Pilot Setup
  • Troubleshooting: WiFi & GPS
  • SkyDemon Setup
  • Stratux Web Interface
Contact
🇬🇧EN🇩🇪DE🇪🇸ES
🇬🇧EN🇩🇪DE🇪🇸ES
  1. Home
  2. Dross:Aviation
  3. DIY Guide

DIY Stratux Guide

How to build and upgrade your own anti-collision system

Want to build your own Stratux (OGN) FLARM or upgrade and modify your existing system? Find step-by-step instructions below on how to develop your own anti-collision system for private aviation and gliders.

Build From Scratch

Start with our component list and build your complete Stratux system step by step.

View Component List

Buy Pre-Built

Don't want to build? Browse our ready-to-fly Stratux systems with full support.

Browse Shop

First Time SetupRecommended

Congratulations on your purchase! Please read the instructions before powering on your Stratux for the first time.

Read Instructions

Tools & Resources

Make sure you have these tools ready before starting your build.

Physical Tools

SD Card ReaderRequired

USB or built-in

WiFi-enabled DeviceRequired

Phone/tablet for initial setup

Soldering IronOptional

Only for sensor upgrades

USB-C Data CableOptional

For T-Beam/T-Motion flashing

Small Phillips ScrewdriverOptional

For case assembly

Software & Online Tools

These free tools help you flash, format, calibrate, and debug your Stratux system.

balenaEtcher

Flash firmware images onto SD cards

SD Card Formatter

Format microSD cards before flashing

FLARM/OGN Range Analyzer

Analyze FLARM signal range from OGN data

OGN Live Tracker

Real-time OGN aircraft tracking map

Raspberry Pi Imager

Alternative to balenaEtcher for flashing

Kalibrate-RTL

Calculate SDR PPM offset via GSM stations

PuTTY

SSH client for Stratux debugging

Meshtastic Flasher

Flash Meshtastic firmware via browser

1Getting Started

Start here to gather components, flash firmware, and configure your Stratux for the first time.

DIY Component List

Complete part list for building your own Stratux (OGN) FLARM system from scratch

Install EU/US Firmware

How to flash Stratux EU or US firmware onto your SD card

Parts:
SD Card

Install VFR Charts

Add Open FlightMap Europe or VFR Sectional Charts for the US

Parts:
SD Card

2SDR Configuration

Fine-tune your SDR receivers for optimal ADS-B and FLARM signal reception.

Calibrate NooElec SDR

How to calibrate NooElec Nano 2 SDRs to 868MHz for FLARM reception

Parts:
SDR Receiver

3T-Beam & OGN Flashing

Program your T-Beam or T-Motion module to enable OGN/FLARM transmission capabilities.

Flash TTGO T-Beam (ESP32)

Program the TTGO T-Beam ESP32 module from LilyGo for OGN transmission

Parts:
T-Beam 868MHz

Flash softRF T-Motion (STM32)

Program the softRF TTGO T-Motion STM32 module from LilyGo

Parts:
T-Motion Module

4Sensor Upgrades

Enhance your Stratux with barometric pressure and AHRS sensors for altitude and attitude data.

Add Pressure Altitude Sensor

Install a barometric pressure sensor to your T-Beam for altitude data

Parts:
BMP280 Sensor

Add Altitude Sensor to softRF

Add altitude sensing capability to your softRF or T-Motion device

Parts:
BMP280 Sensor

Add AHRS/Altitude Sensor

Install AHRS and altitude sensors to your Stratux for attitude data

Parts:
Assembled AHRS SensorSensor Adapter Board

Power and USB load when adding senders

Two senders plus two SDRs can overload the Pi's shared ~1,200 mA USB budget and cause the T-Beam to drop out after a few minutes. See why it happens, and how our unique AHRS sensor board fixes it.

Parts:
AHRS Sensor Board

5Usage & Configuration

Learn how to access and configure your Stratux via its built-in web interface.

Stratux Web Interface

Learn how to access, configure and monitor your Stratux at 192.168.10.1

Roastbeef Web Interface

Advanced Roastbeef firmware interface with 17 sections (cockpit display, EMS, radio, autopilot & more)

GxAirCom Web Interface

Configure the GxAirCom firmware on a T-Beam for FLARM transmission at 192.168.4.1

Submit to OGN

Register your device with the Open Glider Network for tracking

Feed the Networks

Pass your airfield's reception on to OGN and the open ADS-B aggregators

Ground Station

A free browser tower screen for your field, from OGN, ADS-B and OpenSky

Mobile Data While Connected

Keep your phone's mobile data (internet) alive while connected to the Stratux WiFi, using WiFi Direct

SkyDemon Setup

Connect over FLARM-NMEA or GDL90 - the receiver's IP address decides which, and it matters

ForeFlight Setup

GDL90 only, nothing to pair - and the one receiver setting that decides whether European traffic is drawn

Maintenance

What ages first - the mount, the connector, the cable - and the five minutes a year that prevent most of it

Troubleshooting: WiFi & GPS

Why the network will not appear, why the tablet leaves it, and why the app uses the wrong GPS

Garmin Pilot Setup

Connect your Stratux to Garmin Pilot over GDL90 for traffic, GPS position and attitude

DIY Component Checklist

Core ComponentsView all

Essential hardware required for every Stratux build. Start with these foundational components.

Selection checkboxComponentDescriptionDross:AviationAmazonAliExpress
Raspberry Pi 3B+ or Pi 4Required

Main processing unit for Stratux

Main processing unit for Stratux-Buy-
SDR Receiver: NooElec Nano 2, 2+, 3Required

Dual receivers for ADS-B and FLARM

Dual receivers for ADS-B and FLARMBuy hereBuy-
SD Card (16GB+)Required

For Stratux firmware and data logging

For Stratux firmware and data loggingBuy hereBuy-
Power Supply (5V 3A)Required

Reliable power for stable operation

Reliable power for stable operation-Buy-

Enclosure / CasesView all

Protect your Stratux with a proper case for cockpit use.

Selection checkboxComponentDescriptionDross:AviationAmazonAliExpress
Case for Stratux Dual ProRecommended

Supports 2x T-Beam modules

Supports 2x T-Beam modulesBuy here--
Case for Stratux ProRecommended

Custom case for Stratux builds

Custom case for Stratux buildsBuy here--
Case for Standard Stratux

Fits RX-only Stratux with AHRS

Fits RX-only Stratux with AHRSBuy here--
Case for Stratux ClassicDiscontinued

T-Beam Stratux Case 2.0

T-Beam Stratux Case 2.0Buy here--
Case for Stratux Dongle

Compact case for dongle edition

Compact case for dongle editionBuy here--
Suction Cup Mount for StratuxRecommended

For window mounting

For window mountingBuy here--
6 Suction Cups for Stratux Case

Add suction cups directly to the case. No mount needed

Add suction cups directly to the case. No mount needed---

SensorsView all

Add AHRS and altitude sensing to your Stratux for enhanced situational awareness.

Selection checkboxComponentDescriptionDross:AviationAmazonAliExpress
Assembled & Ready to Fly AHRS + Pressure Sensor BoardRecommendedNew

Plug & play sensor board, no soldering

Plug & play sensor board, no solderingBuy here--
Adapter Board for AHRS/ Pressure SensorsRecommendedNew

Fits US-style cases (ICM-20948/MPU9250/GY91)

Fits US-style cases (ICM-20948/MPU9250/GY91)Buy here--
AHRS Sensor ICM-20948New

For artificial horizon display

For artificial horizon display Buy here--
AHRS Sensor GY91 (MPU-9250 + BMP280)

Combined AHRS and pressure sensor

Combined AHRS and pressure sensorBuy here--
AHRS Sensor GY-MPU-9255

Alternative AHRS sensor option

Alternative AHRS sensor optionBuy here--
Pressure Sensor BMP388New

Higher precision barometric sensor

Higher precision barometric sensor---
Pressure Sensor BMP280

For accurate pressure altitude

For accurate pressure altitudeBuy here--

AntennasView all

Proper antennas are critical for good reception of traffic signals.

Selection checkboxComponentDescriptionDross:AviationAmazonAliExpress
1090MHz ADS-B AntennaRequired

For ADS-B traffic reception

For ADS-B traffic reception Buy here--
868MHz FLARM/OGN AntennaRequired

For FLARM and Open Glider Network

For FLARM and Open Glider Network Buy here--
2 in 1 Antenna (868MHz FLARM/ OGN + GPS Antenna)RecommendedNew

Combined FLARM/OGN and GPS antenna

Combined FLARM/OGN and GPS antennaBuy here--
978MHz ADS-B UAT Antenna (USA)

For US ADS-B UAT reception

For US ADS-B UAT receptionBuy here--
GPS Antenna (external)

For better GPS accuracy

For better GPS accuracyBuy here--
GPS Antenna internal (IPEX)

Internal IPEX GPS antenna

Internal IPEX GPS antennaBuy here--
GPS Antenna internal (USB)

Internal USB GPS antenna

Internal USB GPS antennaBuy here--
Window Antenna MountNew

Suction cup mount for aircraft windows

Suction cup mount for aircraft windowsBuy here--

Transmission (Optional)View all

Add transmission capability to make your aircraft visible to other pilots.

Selection checkboxComponentDescriptionDross:AviationAmazonAliExpress
T-Beam Module - custom development for Dross:AviationNew

For OGN/FLARM transmission

For OGN/FLARM transmission Buy here--
T-Motion Module

Compact alternative to T-Beam

Compact alternative to T-Beam Buy here--

Cooling & ToolsView all

Keep your Stratux cool and have the right tools for assembly.

Selection checkboxComponentDescriptionDross:AviationAmazonAliExpress
Passive Heatsink

Silent cooling for Raspberry Pi

Silent cooling for Raspberry PiBuy here--
Brushless Fan (40x40mm)Recommended

Fan with custom cable length

Fan with custom cable lengthBuy here--
Brushless Fan (30x30mm)

Fan with custom cable length

Fan with custom cable lengthBuy here--
Screwdriver Set

Precision screwdrivers for assembly

Precision screwdrivers for assembly-Buy-
USB-A to Micro USB Cable for T-BeamRecommended

Custom length, double shielded

Custom length, double shielded---
IPEX to SMA Adapter Cable

Connect T-Beam to ext Antennas

Connect T-Beam to ext Antennas---
SMA Male to MCX Male

To connect NooElec SDR directly to SMA Antenna

To connect NooElec SDR directly to SMA Antenna---
USB-A ExtenderNew

Needed for Stratux (Dual) Pro

Needed for Stratux (Dual) Pro--Buy

* Some links are affiliate links. If you purchase through these links, we may earn a small commission at no extra cost to you. This helps us maintain this site.

Stratux Community & Support

Professional Services

Upgrade, repair, custom build & more

GitHub Repository

Official Stratux wiki & source

Roastbeef Firmware

Advanced Stratux firmware

GXAirCom Wiki

Alternative T-Beam firmware

Discord Channel

Stratux & T-Beam community

Reddit Channel

r/stratux community

SoftRF Wiki

SoftRF firmware docs

Gitter Channel

SoftRF / T-Motion support

ADSB-Out

Software ADS-B Out project

UL-Forum (German)

Stratux Europe Edition Hardware

3D-Printable Cases

Community case designs

Dross Aviation 3D Prints

Our Thingiverse designs

Need Help?

Contact our support team

Need Components or Pre-Built Systems?

Browse our shop for individual components, sensors, antennas, or complete ready-to-fly Stratux systems. All products configured for European frequencies.

Browse ShopView Stratux Systems

Disclaimer

Stratux is not certified aviation equipment. It does not replace a transponder or relieve the pilot of traffic awareness responsibilities. Use as supplementary situational awareness only. Dross:Aviation assumes no responsibility or liability for the use of Stratux devices, firmware flashing, or hardware modifications. All DIY guides are provided without warranty: use at your own risk.

Dross:Aviation

© 2026 All rights reserved.

Dross:Network|Alexander Dross|Dross:Media|Dross:Air|Blog|AIP:Aero|Trade:Aero
Shop|Services|Guides|Comparisons|DIY|Sitemap
Newsletter|Legal|Privacy|Imprint|Contact