Keeping a Stratux reliable

What ages, in the order it actually fails - and the five minutes a year that prevent most of it

Ask what breaks on a receiver that has flown three seasons and the answer is almost never the computer. It is the suction cup that has gone hard, the connector that was mated two hundred times, the thin coax that has been bent against the same edge of the glareshield since 2023. Those are maintenance items, they are all visible from the pilot's seat, and none of them needs a tool.

What fails, in order

Ordered by how often it actually happens, not by how technical it sounds. The first three are mechanical and the fourth is a setting.

  1. 1The mount — Suction loses its grip with cold glass, dust and a cup that has hardened in the sun. It lets go on a warm afternoon, not on the day you tested it.
  2. 2The connector — SMA is rated for a few hundred mating cycles, not thousands, and a connector tightened with pliers is finished sooner than one done up by hand.
  3. 3The cable — Thin coax breaks inside its jacket where it is bent over the same edge every flight. From outside it looks perfect while reception halves.
  4. 4The calibration — The 868 MHz receiver's frequency reference drifts with age and heat. Nothing looks broken; glider traffic simply stops appearing.
  5. 5The memory card — Cheap cards die eventually even on a read-only filesystem. The failure is total and obvious: it stops booting.
  6. 6The board — Last, and usually because of heat or a supply that was never adequate. A board that is cool and properly fed outlives the aircraft's avionics.

The mount and the antenna

A suction cup is a consumable. It holds by a thin film of air pressure against a clean, smooth, non-porous surface, and everything about a cockpit works against that: dust on the glass, grease from fingers, cold that stiffens the rubber, and sunlight that hardens it permanently over a couple of seasons. Press it back on before every flight and watch the arm for a few seconds - if it creeps, the cup is due for replacement rather than another go.

Treat this as a loose-object check, not a convenience check. A mount that releases in flight puts a receiver, a cable and an antenna somewhere in the cockpit of your choosing - and the one place you do not want them is around the controls.

Fewer parts, less to maintain

Every separate antenna is its own housing, its own cable run and its own connector - which is to say its own three ways to work loose. A combined antenna that carries the 868 MHz element and an active GPS patch in one sealed housing halves that count: one part to mount, one cable to route, one connector to check. It also removes the separate GPS puck, which is the part most often left lying on the glareshield because nobody made a place for it.

Two details that matter when you fit one: the 868 MHz element wants to stand vertical, which is what the tilt in a proper mount is for, and the GPS patch wants sky rather than wing. A heated or metallised windscreen attenuates the GPS signal badly, so a side window usually beats the front one.

What we make for this

Connectors and cable

  • Finger-tight is the specification, not a compromise. An SMA nut tightened with pliers deforms the dielectric and the connector degrades from that moment on.
  • Leave the antenna connected between flights where you can. Most connector wear is mating cycles, and the cycles you save are free.
  • Give the cable a loop of slack at the device so that pulling the mount pulls the loop and not the connector. This single habit prevents most broken pigtails.
  • Run it where it is not trapped by a seat rail, a door seal or a control. Thin coax that is pinched once is damaged permanently, even when it still works that day.
  • Check the cable by feel, not by eye: run it through your fingers and look for a soft spot or a kink. The jacket hides the break.

The one setting that ages

The 868 MHz side depends on the receiver being frequency-corrected, and that correction is not a constant: the crystal it compensates for drifts with temperature and with years. The failure mode is quiet. Nothing errors, the status page looks healthy, and gliders stop appearing - which a pilot reads as a thin day rather than as a receiver that has walked off frequency. Recalibrate once a season, and whenever the traffic picture on that band gets noticeably sparser than you remember.

Calibration guide

Heat, dust and the fan

The project recommends a 5 V fan outright, because without cooling the board or the radios can overheat. A fan is also the only moving part in the device, which makes it the only part with a service life: bearings get noisy, blades collect the dust that a cockpit has plenty of, and a blocked vent undoes the whole arrangement. Blow it out once a season and listen to it when you power up - a fan that has started to rattle is telling you something the status page never will.

The memory card and the spare

Recent builds run a read-only filesystem, so the card is not written to in flight and pulling the power does not corrupt it. That removes the usual cause of death but not the card itself, and when one does fail the device simply stops booting. The standard repair is to write a fresh card, which is why the cheapest insurance in this whole page is a second card, imaged and left in the flight bag. Write it at the same time you update, so the spare is never the old version you had forgotten about.

Write a card

The whole schedule

Three lists, and the longest of them takes five minutes.

Every flight

  • Press the suction cup back onto clean glass and give the arm a push.
  • Check the cable is free, with its loop of slack still at the device.
  • Confirm the satellite count and a traffic count that is not stuck at zero.

Every season

  • Run the cable through your fingers; replace it at the first soft spot.
  • Check the SMA connectors are finger-tight and the threads are clean.
  • Recalibrate the 868 MHz receiver.
  • Blow the dust out of the vents and listen to the fan on start-up.
  • Replace a suction cup that creeps, rather than giving it another flight.

Once a year

  • Write a fresh memory card and keep the previous one as the spare.
  • Check the power bank under load rather than by its charge indicator.
  • Replace the USB cable if it has lived in the aircraft all year.

Should you update?

Not reflexively. A receiver that works is doing the job it was bought for, and the middle of a flying season is a poor time to find out what changed. Update when something you need is in the release, when you are about to rely on the device somewhere new, or when the spare card is due anyway - and write the new version to the spare first, so the card that is flying stays the one you have already proved.

Questions that keep coming back

My suction cup falls off in winter - is it defective?
Usually not. Cold rubber is stiff rubber, and stiff rubber does not seal against glass. Warm the cup in your hands before you press it on, and clean the glass - the two together fix most winter cases. A cup that still creeps when warm is worn out.
Reception got worse and nothing changed
Something did change, slowly. Check in this order: the antenna is still vertical and still where it was, the cable has no soft spot, the connector is tight, and the 868 MHz calibration is current. The first three are mechanical and take a minute; the fourth is the one people never suspect.
Can I leave the receiver in the aircraft?
The electronics will survive it; the consumables will not enjoy it. A parked cockpit in summer is the hottest place the device will ever sit, and that heat is exactly what hardens the suction cup and ages a power bank. If it stays, take the cup and the battery with you.
How do I know the calibration is still good?
By comparison, not by a reading. If the band that carries gliders and microlights shows noticeably less than it did last year at the same field on a similar day, calibrate before you look for anything else.

Cooling and calibration requirements from the Stratux project's supported-hardware wiki

Disclaimer

Stratux is not certified aviation equipment. It does not replace a transponder or relieve the pilot of traffic awareness responsibilities. Use as supplementary situational awareness only. Dross:Aviation assumes no responsibility or liability for the use of Stratux devices, firmware flashing, or hardware modifications. All DIY guides are provided without warranty: use at your own risk.