Power and battery life

What a receiver draws, what the supply must give, and why the cable is usually the culprit

Intermittent faults in a Stratux are power faults far more often than software faults. The receiver is a small computer with two radios hanging off its USB bus, and it fails the way small computers fail when the volts sag: it reboots, drops the transmitter, or loses a radio and carries on looking healthy. Three numbers settle almost every case.

What it actually draws

Continuous draw~1 A @ 5 V

The project's own figure, and the basis for its rule of thumb of one amp-hour per hour of use.

Supply rating≥ 2.1 A

The project's minimum, for the peaks: boot, WiFi bursts and an 868 MHz sender transmitting. In practice take more - a source that genuinely holds 2.5 to 3 A is what stops boot failures.

Shared USB budget~1,200 mA

Everything plugged into the board shares this. Two radios and two senders sit right at the edge of it.

Board generation3B < 4B < 5B

Each newer board draws more than the one before it, so a supply that was adequate on an older build may not be.

The cable is usually the fault

Current through a thin conductor costs voltage, and a USB cable sold for charging a phone is built for exactly that and nothing more. Draw an amp through two metres of it and the five volts that left the supply arrive as something the board reads as a brownout. The receiver does not report this as a power problem - it reboots, or a radio disappears, or the transmitter stops and the traffic picture quietly halves.

The board does say so, in its own way: a red power LED that blinks or goes dark means it is seeing low voltage. That is a cable or supply verdict, not a diagnosis of anything downstream.

  • Short and thick beats long and thin. Half a metre of decent cable is worth more than any power bank upgrade.
  • Test the cable, not the theory: swap it for a known good one and see whether the fault follows the cable.
  • A power bank reading full proves nothing. Capacity and delivery are different properties.

Runtime, honestly calculated

The capacity printed on a power bank is measured at the cell, around 3.7 V, not at the 5 V it hands out. Convert before you plan: multiply the printed milliamp-hours by 3.7 to get watt-hours, divide by 5 for the amp-hours you will actually see, then take off the conversion losses - a fifth is a fair allowance. What is left, divided by the one amp the receiver draws, is your flying time.

5,000 mAh

about 3 hours

10,000 mAh

about 6 hours

20,000 mAh

about 12 hours

Two conditions sit behind those figures: the bank must sustain 2.1 A, and it must not switch itself off when the draw dips - some small banks interpret a quiet moment as "nothing connected". If you charge the bank while it feeds the receiver, it needs pass-through charging, which many do not have.

We ship no batteries with our units, so this is deliberately arithmetic and not a product recommendation: buy the bank where you buy batteries, and judge it on sustained current rather than on the number on the case.

Running it off the aircraft

  • A converter from the aircraft bus to 5 V has to hold its output while the bus does anything but sit still. Judge it by its continuous rating, and leave margin above the 2.1 A figure rather than meeting it exactly.
  • Switch it like a radio: on last, after the engine is running, and off first, before shutdown. The spikes that come with starting and stopping an engine are what destroy small electronics, and the receiver has no more protection against them than the radio does.
  • Fuse the feed, and route the cable where it cannot chafe or be pulled. A connector that works loose in flight looks exactly like a software fault from the cockpit.

Why a Dual Pro is the hard case

Everything plugged into the board shares one current budget of roughly 1,200 mA. Two radios and a single sender fit inside it. Two radios and two senders do not, quite: the senders are idle most of the time and then transmit, and the peak is where the budget breaks. The symptom is a device that works on the bench for an hour and drops a sender in flight - which reads as a radio fault and is a power fault.

What a USB port may actually give

One USB 2.0 port500 mA

The specification figure, and what a receiver dongle is designed around.

One USB 3.0 port900 mA

More per port, but it does not raise what the board as a whole may hand out.

All ports together~1,200 mA

The number that decides it. Four ports do not mean four budgets - they share this one.

A bigger power bank does not solve this, because the limit is on the board and not upstream of it. What solves it is taking the senders off that shared budget - which is exactly what our current AHRS sensor boards are built to do: they feed the senders past the USB budget and smooth the draw during transmit peaks, so two T-Beams and two SDRs run without dropouts, with no cable surgery and no external power modification.

Heat, the other half of the same problem

The project recommends a 5 V fan outright, because without one the board or the radios can overheat - and a hot board throttles, which looks like a slow or stuttering receiver rather than a thermal fault. A cockpit in summer sun is a worse environment than a desk, the case is closed, and the radios run warm by design. Passive cooling helps; airflow helps more.

Cooling

Can you just pull the plug?

Yes, and that is by design: recent builds run a read-only filesystem precisely so that losing power costs nothing. That answers the question people ask about the SD card, but it does not change the advice about the aircraft bus - there the reason to shut down first is the voltage spike at engine stop, not the filesystem.

Questions that keep coming back

My power bank says 3 A, so why does it still cut out?
Because the figure on the case is a maximum across all ports under ideal conditions, not a promise about one port with a warm cell at twenty percent charge. Judge a bank on whether it holds up at the end of its charge, which is the only part of the flight where it matters.
Does the transmitter change the numbers?
Not the average much, but the peaks a great deal, and peaks are what trip a marginal supply. A receiving-only build is forgiving; add one sender and the supply matters; add two and the board's own budget becomes the limit.
Is a USB-C charger from a laptop a good supply?
Usually yes on the ground, where it can negotiate a sensible voltage and has a short cable. It says nothing about the airborne case, which is about a bus that sags and spikes rather than about available watts.
The receiver restarts on a bumpy taxiway
That is mechanical, not electrical: a connector that is almost making contact. Vibration finds every loose plug long before the pilot does. Strain-relieve the cable at the device and the symptom goes with it.

Disclaimer

Stratux is not certified aviation equipment. It does not replace a transponder or relieve the pilot of traffic awareness responsibilities. Use as supplementary situational awareness only. Dross:Aviation assumes no responsibility or liability for the use of Stratux devices, firmware flashing, or hardware modifications. All DIY guides are provided without warranty: use at your own risk.